RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: wmg706
Showing results 1 to 16 of 16
Search took 0.07 seconds.
Forum: ARF or RTF
01-03-2010, 06:48 PM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

Thanks for the offer Avaiojet but if you go back to page 9 of this forum there are photos of my plane finished I put the cowl and tail decal on after the crash the others I still havent put on Its...
Forum: ARF or RTF
01-03-2010, 10:54 AM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

Dont give up I piled mine up pretty bad in a stall 1st flight . Smashed first 3" of fuse but it whet back together and flies again.
Forum: ARF or RTF
12-26-2009, 04:04 PM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

I'm Running a Master airscrew 16x8 with a Zenoah G26ei .Pulls it just fine Mine flys great
Forum: ARF or RTF
12-25-2009, 10:30 AM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

I did pretty much the same as R/C Foolish 4 1/2 dubros dremmeled the bottom of' the wheel pants ,bought 1/2"alumimun spacers or about 1/2 " for both sides of each wheel I"ve been landing on paved...
Forum: ARF or RTF
12-17-2009, 07:11 AM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

I cut about a 1 1/2 to 2" length of brass fuel line and fiberglassed it inside the hole of the wheel pant. Then cut the cables to fit and crimped a small piece of brass tubing 1/18 long for my loop...
Forum: ARF or RTF
12-16-2009, 04:21 PM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

I think a pitts would fit with no problem there is plenty of room I did'nt have to cut a hole for the carb just cut one to vent exhaust ann reach spark plug if I needed to.
Forum: ARF or RTF
12-16-2009, 07:47 AM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

Don't know what the weight is C G set per manual . Flying in 15 to 20 mph breeze it just don't need elev. on down wind run. Mine will slow fly but we have been flying a pylon pattern.
Forum: ARF or RTF
12-15-2009, 09:47 PM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

You have toland it with alittle power don't cut the throttle until your touching down or it will drop and bounce and nose over .Use very very little elev or she will stall.because she is very short...
Forum: ARF or RTF
12-15-2009, 03:21 PM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

photos gee bee z
Forum: ARF or RTF
12-15-2009, 03:02 PM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

Land with a little power when wheels touch down cut power. I dinged the wheel pants a few times just glassed them with no problem.
The landing gear seems to be holding up well though . I bought...
Forum: ARF or RTF
12-14-2009, 05:42 AM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

Got a zenoah 26 in mine flys it great made a hatch in fuse under tail and mounted both the batteries .With 4 1/2"wheels no problems.Flew it again yesterday did great
Forum: ARF or RTF
11-26-2009, 09:41 AM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

I ordered skylite treaded 5" wheels they should arrive tomorrow.Ill let you know how they work out.
Forum: ARF or RTF
11-25-2009, 08:33 PM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

I glassed brass fuel tube on the inside of the two slots on each wheel pant then ran the cable pulling on each side . I would suggest not flyning the plane until you do that and replace the wheels....
Forum: ARF or RTF
11-05-2009, 08:25 AM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

what did you set your elevator at to Smoth it out?
Forum: ARF or RTF
10-30-2009, 01:07 PM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

How did everyone attach the plastic molding
Forum: ARF or RTF
10-29-2009, 06:14 PM
Replies: 748
Views: 163,625
Posted By wmg706

RE: Seagull Gee Bee Z

I am finishing my gee bee I put a 26 cc Gasser on it is everyone checking cg with plane upside down? Also is 9 cm from leading edge the best balance? Thanks
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.