RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: JDjetjock
Showing results 1 to 11 of 11
Search took 0.01 seconds.
Forum: RC Jets
08-28-2022, 07:54 AM
Replies: 577
Views: 121,747
Posted By JDjetjock

Hi Ron, In my F-4, I have a Jetcentral...

Hi Ron,

In my F-4, I have a Jetcentral Mammoth inside a bypass using the stock rail mounting angle and the stock tail pipe. The pipe is not inverted, but the pipe outlet is located at the lower...
Forum: RC Jets
09-10-2018, 05:54 PM
Replies: 577
Views: 121,747
Posted By JDjetjock

Congrats Kevin! Looking good! I gotta get some...

Congrats Kevin! Looking good! I gotta get some AIM-7s for my F4 too.

Any Phantom drivers going to Max Smart's jet event at Plattsburgh, NY in a couple weeks?
Forum: RC Jets
08-24-2018, 12:41 PM
Replies: 577
Views: 121,747
Posted By JDjetjock

Hi Kevin, For the centerline tank, I mounted...

Hi Kevin,

For the centerline tank, I mounted the tank lined up with the break point on the fuse with the nose section. It also lines up with a large molded former line at the rear of the tank. See...
Forum: RC Jets
08-02-2018, 04:09 PM
Replies: 577
Views: 121,747
Posted By JDjetjock

I use the JMP high flow valve on the mains, a...

I use the JMP high flow valve on the mains, a robart one on the nose and the stock Skymaster valve on the doors. I have separate air systems for the gear, doors and brakes! Air tanks are light,so...
Forum: RC Jets
07-10-2017, 05:16 PM
Replies: 577
Views: 121,747
Posted By JDjetjock

Hi Don, sent you a PM. Cheers,

Hi Don, sent you a PM.

Cheers,
Forum: RC Jets
07-03-2017, 05:34 PM
Replies: 577
Views: 121,747
Posted By JDjetjock

Here's some other pics of the tailpipe, landing...

Here's some other pics of the tailpipe, landing gear reinforcement and h-stab neutral posn. The hstab for trimmed flight at my CG is 46mm below that mold line. Note the small amounts of up-elevator...
Forum: RC Jets
07-03-2017, 04:25 PM
Replies: 577
Views: 121,747
Posted By JDjetjock

Guys, Here's the CG for my F-4 for different...

Guys,

Here's the CG for my F-4 for different fuel states (Jet-A):
- full tanks (take-off): 302 mm (weight 53.3 lbs)
- front tank filled to the seam (approx 50% full), rear tanks empty - typical...
Forum: RC Jets
07-03-2017, 12:15 PM
Replies: 577
Views: 121,747
Posted By JDjetjock

Guys, I'm using the standard feed of the tanks...

Guys,
I'm using the standard feed of the tanks (rear tanks in parallel feeding the front tank). After a 6.5 to 7 minute flight, the front tank is between 50% to 90% full. I find that flaring for...
Forum: RC Jets
07-03-2017, 06:48 AM
Replies: 577
Views: 121,747
Posted By JDjetjock

Hi Chris, The config is ready for flight,...

Hi Chris,

The config is ready for flight, tanks empty except the UAT/CAT tank full, and gear down, and no external stores. At idle it is well behaved, and landing approaches feel good with a...
Forum: RC Jets
07-03-2017, 06:32 AM
Replies: 577
Views: 121,747
Posted By JDjetjock

Yes, I removed material from the lower section of...

Yes, I removed material from the lower section of the tail cones. I can provide a pic if you would like. I recommend to maintain the downthrust angle of the engine mount...I measured it and if I...
Forum: RC Jets
07-02-2017, 06:31 PM
Replies: 577
Views: 121,747
Posted By JDjetjock

For my F-4E, I found the CofG sweet spot to be...

For my F-4E, I found the CofG sweet spot to be 325mm, I have no tail blanking probs with flaps down. Inverted flight at that setting is nice too.

For the tailpipe, I have stuck with the stock...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.