RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: cygnet
Showing results 1 to 18 of 18
Search took 0.06 seconds.
Forum: Classic RC Pattern Flying
06-11-2009, 07:16 PM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

This is interesting my TF plans show a v bottom and my kit has a v former I wonder if there are two different TF plans
Forum: Classic RC Pattern Flying
06-11-2009, 12:11 AM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

Duane I just checked my Kit and my plans and the bottom is V thats why he used the wood lenght ways by the way I build my scratch the same way you did just seems to make more sense.
Forum: Classic RC Pattern Flying
04-27-2009, 11:44 PM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

No doubt Ed changed things at will I think thats why he built the Silma the way he did ie wings that could be changed at will. I think we should just pick one as we may never know how many versions...
Forum: Classic RC Pattern Flying
04-26-2009, 10:27 AM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

Well there is another way to do it also, the old ACE RC kits of the 80's, the ones I'm refering too are the ACE Extra 260 series. These used a wooden spar plug in wing system, its very light and...
Forum: Classic RC Pattern Flying
04-25-2009, 10:16 PM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

The type of foam cutting that they used in the picture is very high tech even by todays standards. I have cut a lot of foam wings and to hollow them out that way is very time consuming, it can be...
Forum: Classic RC Pattern Flying
04-25-2009, 10:42 AM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

We are getting closer, but we have to decide on the type of construction, on a Taurus Ed used off set spars with no shear webs but the Simla has plug in wings with 4in dihedhal so we need to come up...
Forum: Classic RC Pattern Flying
04-24-2009, 11:12 PM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

I use Lion's they are 100% safe and they are good to around a 1000 cycles the down side is that they are a little heaver and 1/10 of a volt less but if you need all out power just go up one more S...
Forum: Classic RC Pattern Flying
04-24-2009, 07:13 PM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

If you guys can come up with a set of plans for the Silma I'm in, I would like to use electric that way we can fly it any way we like. If we want more power we just add more series in the battery,...
Forum: Classic RC Pattern Flying
04-21-2009, 12:02 AM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

Does anyone know what happened to the simla? I mean where did it end up?
Forum: Classic RC Pattern Flying
04-08-2009, 11:48 PM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

I think Ed stayed with the airfoil beacuse of the radio equipment of the day, if you have ever flowen a reed radio you will know what I mean, you want all the stability you can get things move really...
Forum: Classic RC Pattern Flying
04-07-2009, 09:16 PM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

I always entered the sping with just the elevator and rudder but you could tighten up the spin with the ailerons, as for shimming up the wing no just left it stock. The only time that spinning was...
Forum: Classic RC Pattern Flying
04-07-2009, 09:06 PM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

Mine was 6lbs and had a Gold cup 61 in it. The CG was just ahead of the landing gear block if you pushed the tail down it would stay down.
Forum: Classic RC Pattern Flying
04-06-2009, 11:21 PM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

Lots of talk about the spin I flew a Taurus for many years in competition and never had a problem with the spin or the snap, as a matter of fact you have to be careful when doing snaps the stab has...
Forum: Classic RC Pattern Flying
04-03-2009, 10:01 PM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

Hi guys sorry for the slow reply W1 is 11-3/16 but you have to add 3/32 leading edge sheeting and 1/8 trailing edge square, W12 is 7-5/16 plus the 3/32 leading edge sheeting and the 1/8 trailing edge...
Forum: Classic RC Pattern Flying
04-01-2009, 10:10 PM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

USTIK I have a original top flite kit what do you need to know?
Forum: Classic RC Pattern Flying
02-21-2009, 02:06 AM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

Now that's one good looking plane I also would be very interested in more info on the Simla I would love to build one, maybe one day some one will come up with enought info or some sort of drawing we...
Forum: Classic RC Pattern Flying
02-19-2009, 08:42 PM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

I think you are right there is a lot of Taurus in a King altair I'm in the process of building a Taurus my buddy is builting a King we were compairing the two the construction is just about the same...
Forum: Classic RC Pattern Flying
02-13-2009, 10:02 PM
Replies: 2,649
Views: 372,045
Posted By cygnet

RE: Ed Kazmurski's Taurus

Just to chim in here did ED not own a machine shop? I think he did and he could make a clip out of any metal he wanted to, I bet those clips are made out of good stuff and not filed, any way guys I...
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.